[Rivet] Rivet 2.0.0rc (release candidate) for testing

Dmitri Konstantinov Dmitri.Konstantinov at cern.ch
Wed Oct 9 11:18:48 BST 2013


Hi Andy,

I have tried to run rivet 2.0.0rc from temporary installation place:

source /afs/cern.ch/sw/lcg/external/gcc/4.8.0/x86_64-slc6-gcc48-opt/setup.sh

cd 
/afs/cern.ch/cms/CAF/CMSCOMM/COMM_ECAL/dkonst/GENSER/lcgcmake-install-preview/MCGenerators_lcgcmtpreview/rivet/2.0.0rc/x86_64-slc6-gcc48-opt/

source ../rivetenv.sh

./rivet --help

And it says:

-bash-4.1$ rivet --help
The rivet Python module could not be loaded: is your PYTHONPATH set 
correctly?

While same procedure for rivet 1.8.3 works for me.
( 
/afs/cern.ch/cms/CAF/CMSCOMM/COMM_ECAL/dkonst/GENSER/lcgcmake-install-preview/MCGenerators_lcgcmtpreview/rivet/1.8.3/x86_64-slc6-gcc48-opt/bin/ 
)

For both cases my initial (before rivetenv.sh execution) PYTHONPATH was 
not defined.

Could you please take a look?

Cheers,
  Dima


On 10/9/13 12:00 PM, Dmitri Konstantinov wrote:
> Hi Andy,
>
> Great news! :)
>
> From genser side we have added Rivet 2.0.0rc and YODA 1.0.3 to our 
> preview configuration.
> It was successfully compiled for x86_64-slc6-gcc48-opt, 
> x86_64-slc6-gcc46-opt, x86_64-slc5-gcc46-opt, x86_64-mac108-gcc42.
>
> Though I have not tried to run rivet itself.
>
> Cheers,
>        Dima
>
>
>
> On 10/9/13 1:56 AM, Andy Buckley wrote:
>> Hi Anton and Genser,
>>
>> We *finally* have a release candidate for Rivet 2.0.0! This has taken an
>> extraordinary length of time to make... but the testing was definitely
>> worth doing and it's the best Rivet yet. We hope to make the proper
>> 2.0.0 release in the next few days, but it's best that we provide you
>> with a preview to test that we didn't break anything in the last few
>> updates! It works fine on my system, on lxplus6, and in our automated
>> build system, so hopefully there should be no problems.
>>
>> Could you please run a quick test build, and a couple of analyses in
>> mcplots if you have a setup to use our YODA histogram interface already,
>> and let us know if you encounter any problems? The code to use is the
>> Rivet 2.0.0rc tarball from http://www.hepforge.org/downloads/rivet , and
>> the new version 1.0.3 of YODA, from 
>> http://www.hepforge.org/downloads/yoda
>>
>> If all goes well, we will release Rivet 2.0.0 this week, and shortly
>> afterward we will produce version 1.8.4 (the guaranteed last point in
>> the 1.x series) and 2.0.1, which will include equal sets of new analysis
>> codes from ATLAS, CMS, and LHCb. Just so you know what is planned ;-)
>>
>> Thanks again,
>> Andy & the rest of the Rivet team
>>
>



More information about the Rivet mailing list